Power supply for handpieces
وحدة بطارية Li-Po (2x3.7 فولت؛ 800 مللي أمبير في الساعة) مع شحن من محطة الشحن
Operating temperature in modes
- تقليم الجوتا بيرتشا 'CUT' - 170 +/- 10 درجة مئوية، - تكثيف الجوتا بيرتشا 'PACK' - 120 +/- 10 درجة مئوية، - التنشيط الحراري للر
Accuracy of stabilisation of Estus Pack operating temperature
2 °م
Maximum duration of the thermoplugger heating cycle with subsequent automatic shutdown in modes
- قطع المطاط 'CUT' - 10 ثوانٍ. - تكثيف المطاط 'PACK' - 20 ثانية - التفعيل الحراري للري 'MIX' - 120 ثانية.
Estus Pack tip runtime with a new fully charged battery pack without recharging.
لا تقل عن 500 دورة تسخين
Operating temperature of Estus Fill tip
180 °م
Accuracy of operating temperature stabilisation in Estus Fill
10 °م
Time of maintaining the operating temperature in Estus Fill in "standby" mode
3
Estus Fill operating time with a new fully charged battery pack without recharging.
13-15 دورة تسخين لمدة 3 دقائق
Time of operation of handpieces in the "standby" mode before automatic power failure
10
Overall dimensions of the Estus Pack nozzle
(207*33*43) ±3 مم
Weight of Estus Pack tip
80 سنة
Overall dimensions of Estus Fill tip
(240*33*43) ±3 مم
Weight of Estus Fill tip
115 سنة
Protection against electric shock for lugs
جهاز بمصدر طاقة داخلي. الجزء العامل من النوع B
Built-in NF-03 radio module in the tips
2,4-2,525 جيجا هرتز، أقصى طاقة خرج - +7 ديسيبل ميلي واط، نطاق - يصل إلى 3 متر على خط الرؤية المباشر
Overall dimensions of "Estus Energy-D" charging station
(87*56*49) ±3 مم
Weight of Estus Energy-D charging station
145 سنة
Parameters of the charging station power supply unit
جهد الإدخال (100-240) فولت، ~50/60 هرتز، جهد الخرج 5 فولت؛ الحد الأقصى 2.4 أمبير.
Overall dimensions of the Estus Two-B stand
(102*100*40) ±3 مم
Weight of "Estus Two-B" stand
One link up to 16GB 64-bit DDR4-2400 MHz with ECC support; 16GB (for CPC1309-01); 8GB (for CPC1309-02) سنة
Adjustment of the working temperature of the Estus Pack handpiece in "PACK" mode in conjunction with the ESTUS MULTI control uni
80...120 °م
Adjustment of the Estus Fill handpiece operating temperature in conjunction with the ESTUS MULTI control unit.
160...200 °م
Max. time for full charging of handpiece battery packs
3
Max. injection needle tip temperature
75 °م
Max. temperature of the external surface of the heater Estus Fill
45 °م
Average time to heat Estus Fill from 20 deg. C to 180 deg. ?
15
Max. time to heat the thermoplugger to the set operating temperature
3
Time of extrusion of whole gutta-percha rod in Estus Fill with accuracy +/- 10 sec.
- لمستوى السرعة «عالي» - 30 ثانية؛ - لمستوى السرعة «متوسط» - 65 ثانية؛ - لمستوى السرعة «منخفض» - 140 ثانية